Loose thread embedment: When the local coil cannot be firmly fixed in the nest, the vibration of the car pressing the road surface will cause the coil in the nest to deform, and change the initial inductance of the ground sense. At this time, the sensor must be reset before it can work normally. The solution is to put the molten asphalt in place and fix it.
Loose wire: The hinge screws are connected by positive and negative threads, and the upper and lower two bearings are connected by a double-headed screw. If the screws are loose, the upper and lower positions will be inaccurate. Use a 80mm long Ф4 iron rod to insert the double-headed screw to adjust the brake lever up and down in place.
Lever screw loose: If this screw is loose, it will cause the upper and lower position of the brake rod to be inaccurate and the shaking when the lever is stopped, tighten the bolt and tighten the nut.
In-position control magnets move position: Cimin Hall elements are used up and down to position. If rectangular magnets and reducer with cams change the position of the wafer, the position is inaccurate. Adjust it accurately and not flip it to solve the problem.
Power-off protection switch power off: When the control part of the machine fails, the automatic protection device of this machine will automatically work. At this moment, the brake lever will stop at the upper position and the main power will be disconnected and the machine will not work. At this point, the machine door is opened, and the large belt can be restored by rotating the large belt 3-8 times clockwise. If it cannot be restored to this condition many times, check whether the Hall element and the circuit board have malfunctioned.
The pull-down hook adjusts the looseness of the nut: the lower part of the chassis is provided with a pull-down hook of thread M10, and its function is to pull the spring of the balance mechanism and the zero adjustment of the balance function. It is equipped with two M10 Hexagon Nuts and ten spring washers. If the nut is loose, knocking noise and balance will occur when the machine is running. Even if the machine can run after the imbalance, it will greatly increase the speed reducer, motor and other transmissions. The load of the parts affects the reliability and the mechanical life.
Loose wire: The hinge screws are connected by positive and negative threads, and the upper and lower two bearings are connected by a double-headed screw. If the screws are loose, the upper and lower positions will be inaccurate. Use a 80mm long Ф4 iron rod to insert the double-headed screw to adjust the brake lever up and down in place.
Lever screw loose: If this screw is loose, it will cause the upper and lower position of the brake rod to be inaccurate and the shaking when the lever is stopped, tighten the bolt and tighten the nut.
In-position control magnets move position: Cimin Hall elements are used up and down to position. If rectangular magnets and reducer with cams change the position of the wafer, the position is inaccurate. Adjust it accurately and not flip it to solve the problem.
Power-off protection switch power off: When the control part of the machine fails, the automatic protection device of this machine will automatically work. At this moment, the brake lever will stop at the upper position and the main power will be disconnected and the machine will not work. At this point, the machine door is opened, and the large belt can be restored by rotating the large belt 3-8 times clockwise. If it cannot be restored to this condition many times, check whether the Hall element and the circuit board have malfunctioned.
The pull-down hook adjusts the looseness of the nut: the lower part of the chassis is provided with a pull-down hook of thread M10, and its function is to pull the spring of the balance mechanism and the zero adjustment of the balance function. It is equipped with two M10 Hexagon Nuts and ten spring washers. If the nut is loose, knocking noise and balance will occur when the machine is running. Even if the machine can run after the imbalance, it will greatly increase the speed reducer, motor and other transmissions. The load of the parts affects the reliability and the mechanical life.
Hex self tapping screws are normally used with sheet metal and plastics. This variant has a hexagon head, so is designed to be driven in with a standard spanner or ratchet and socket. So this type of screw forms its own thread as it is installed into a pre-drilled hole.
Hex tapping-screws are also known as self-tapping screws, these are mostly used in thin gauge sheet metal applications.Stainless steel significantly improves resistance to tarnishing or corrosion.
Hexagon Head Tapping Screws,Hex Head Self Tapping Screws,Rotary Hex Head Self Tapping Screw,Self Tapping Hex Head
Taizhou Wanluo Hardware Products Co., Ltd. , https://www.wlhardware.com