How to test the bearing and shaft cooperation

Source: Bearing network time: 2013-01-23

/*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089';

The cooperation gap between the bearing and the shaft is necessary; the following methods can be used to detect the radial clearance.
1. The ruler detection method is about the bearing with larger diameter; the gap is larger; it is directly detected with a narrow feeler gauge. For the bearing with smaller diameter; the gap is smaller than that of the æ§é˜Œ åŸé¥¬æµš åŸé¥¬æµš å²¢ å²¢ ç‰Ÿå˜žå®æ§åŒ¦èƒ— ç©¸ ç©¸ é’¡ é’¡ é’¡ é’¡ é’¡ é’¡.
2, the lead detection method using the lead method to detect the bearing gap is more accurate with the feeler gauge; but more troublesome. The aluminum wire used for testing should be soft; the diameter should not be too big or too. Noisy this paragraph æ¹Ž pocket 1. 5 ~2 times; in practice, soft lead wire is usually used for testing.
When testing; first open the bearing cover; use the appropriate diameter of the lead wire; cut it into 15~40 mm long section; place it on the journal and the upper and lower bearing interface; cover the bearing cover; tighten according to the regular torque Bolt; then loosen the bolt; remove the bearing cap; use a micrometer to detect the thickness of the flattened wire; find the average value of the bearing top clearance.
If the headspace is too. Slightly thin (11) å³¦å‘“å²· å«” å«” . .. If too large; then reduce the pad, scrape the ground or cast the tile from the head.
Adjustment of bearing bushing force: In order to avoid possible transition and axial movement of the bearing bush during operation; in addition to cooperating with interference and stopping parts; it is necessary to use bearing cap to compress; bearing method and measuring top gap method The same; the thickness of the soft lead wire is measured; the bearing bushing force can be calculated (indicated by the amount of elastic deformation after the bushing is tightened)
Usually, the bearing force of the bearing bush is between 0. 02 and 0. 04 mm. If the pressing force does not meet the specifications, it can be adjusted by increasing or decreasing the thickness of the gasket at the joint surface of the bearing and the bearing seat; the back of the tile is not allowed to be padded.
In addition to ensuring radial clearance, the plain bearings should also ensure axial clearance. When detecting axial clearances; move the shaft to a pole orientation; then measure the axis from one pole to the other with a feeler gauge or dial indicator The amount of turbulence is the axial gap.
When the clearance of the sliding bearing does not conform to the rules; adjustment should be made. The split bearing is often used to adjust the radial clearance (top clearance).

Recommend to friends comments close window

Bearing related knowledge

Sliding bearing characteristics of tandem thrust cylindrical roller bearing layout mode bearing clearance selection criteria medium-sized automobile wheel NSK bearing analysis imported bearing defect specification

This article links to http://
Please indicate China Bearing Network http://

Previous: The reason for the abnormal heating of NSK imported bearings is as follows: The cause of bearing faults and the cause of failure

Palm Oil Mass Flow Meter

Zhejiang Sealand Technology Co., Ltd. is a trustworthy manufacturer of Palm Oil Mass Flow Meter, Palm Oil Mass Flowmeter, Palm Oil Coriolis Mass Flow Meter, Palm Oil Coriolis Mass Flowmeter, Palm Oil Flow Meter, ATEX, IECEx & CE approved.

With its high accuracy, wide rangeability and reliable performance, Sealand meter has been applied in many kinds of industries during the last 8 years. Unlike others who only focus on the measurement of liquid at normal pressure & temperature, Sealand has conquered the difficulty in the measurement under severe conditions, such as high pressure, high viscosity, high & low temperature.

Besides, Sealand lab is
1. Controlled completely by automatic system, to minimize personal error.
2. Equipped with 3 METTLER TOLEDO scales with accuracy 0.014%.
3. Device extended uncertainty: 0.05%.
4. Certified by Zhejiang Institute of Metrology which is authorized by ILAC; Sealand meters are also approved by them after test in their lab with ISO/IEC 17025:2005 standard.

Palm Oil Mass Flow Meter, Palm Oil Mass Flowmeter, Palm Oil Coriolis Mass Flow Meter, Palm Oil Coriolis Mass Flowmeter, Palm Oil Flow Meter

Zhejiang Sealand Technology Co., Ltd. , https://www.sealandflowmeters.com