During the daily decoration process, many owners or decoration and installation masters often find that after the decoration, indoor ceilings, walls, cabinets or painted suite doors sometimes have delamination, cracking and drumming. The main reasons for the problem are: the quality of the materials used is not up to standard, the construction is not rigorous, and the decoration environment is too humid. Then follow the decoration home network Xiaobian to learn about the relevant content!
First, the method of solving the crack at the bottom of the line
When installing the line, please reserve a 3-5mm gap with the ground (to avoid direct contact between the line and the ground), and put a glass glue in the gap to avoid cracking the line due to the wetness of the ground. When installing the sleeve, please reserve 3-5mm gap with the ground (to avoid direct contact between the sleeve and the ground), and put the glass glue in the gap. At the same time, it is required to fill the bottom of the sleeve at a height of 500mm. Foam) to avoid cracking the bottom of the sleeve due to moisture on the floor or wall.
Second, the method of installing the paint set door
1. Measure the position of the door frame. When assembling the door frame, it must be carried out on the ground with lubrication and cleanness. The four horizontal frames are connected with the two vertical frames with four 60mm long screws. The three frame doors are on the same plane, and the top frame and the frame are connected at 90 degrees. Corner, fixed 4 to 6 pieces on both sides of the frame, nailed with lock wood and locking angle wood, the top frame is placed on the top of the two frames, the inner width between the two door door openings should be 6mm larger than the door width. The inner height between the top frame door and the floor should be 13mm higher than the door height.
2. Fixed the door frame. Turn the assembled door frame over the ground and fix 4 to 6 connecting pieces with the nails to see if the inner angle is 90 degrees. The inner width of the middle and lower points on the door frame is not common. Put the assembled and sturdy door frame into the door hole, use the hanging wire hammer to check whether the whole door frame is straight. Use the nail hole of the connecting piece as the point to determine the orientation of the nail hole on the wall. The rivet nails the connecting piece to the wall. The fixed door frame and the wall gap are inserted into the wooden strip or written into the styrofoam, so that the door frame and the wall are firmly connected.
3. When the door leaf is hinged, the upper and lower hinges are first screwed, then the door is closed to check whether the gap is suitable. Check whether the door door and the door leaf are on the same plane, whether the door leaf is falling or not, and the other screws are tightened after the error is correct. Screws are directly inserted into the frame of the door. When the door frame and the door leaf are installed, the door door is guaranteed to be in good position. The door leaf and the door lock switch are sensitive. The gaps between the door and the door are not installed. The joint gap is tight and strong, and the decoration appearance is not damaged. .
The above is a detailed answer to the Xiaobian, I don't know if you are satisfied with the introduction of the decoration home network Xiaobian~ If you want to know more about the exciting content, please continue to pay attention to our decoration encyclopedia!
More related wonderful reading:
How to choose the paint set door? Top ten brands of paint set door
PVC High Speed Door are designed for indoor use and ensure rapid handling operations between different areas that should remain separated. These safe and efficient industrial doors are made of a shaped steel frame and covered with PVC. These high speed doors are safe and efficient and consist of a shaped steel frame covered with PVC. Safety is ensured by their photocells and barriers.
High speed doors protect us from harm, save energy and help us to separate processes for optimal productivity. A high speed door's most important job is to simply open and close quickly and safely every time you need it.
The high speed pvc roll shutter door require high strains, caused by the high operating speed and the frequency of openings, have to be taken into account during construction. In the same way, basic conditions like size and installation location add up to considerable requirements regarding safety and control technique.
PVC High Speed Door,Large PVC High Speed Door,Transparent High Speed Door,Great Performance High Speed Door
Shenzhen Hongfa Automatic Door Co., Ltd. , https://www.hongfadoor.com