1. Check if the bathtub is dripping. Check the bathtub when it is filled with water.
2. Check if the drainage is smooth.
3. Check if the floor drain meets the requirements, splash water on the ground, the water should flow to the floor drain, and there is no residue.
4. The shower room should be strictly in accordance with the assembly process. The assembled shower room is neat and bright. The door and the sliding door are parallel and vertical, and the left and right are symmetrical. The two moving doors are easy to open and close, and the gap is closed without leakage. A silicone seal is applied between the shower room and the shower tray to prevent water seepage.
5. Installation and acceptance of the basin or basin: the level of the basin surface, the joint of the cold and hot water joints should be located at the lower end of the basin, and the cold and hot water taps have obvious identification marks. The bottom foot of the basin should be firmly connected to the floor. After installation, the feet are sealed with silicone and no leakage. The basin must be fixed firmly, and the wooden cabinet should be stably supported under the counter. The basin without the cabinet should be supported by the iron frame and the wall surface, and the wall panel should be placed on the wall to make the water retaining plate. ~12cm; the outside of the countertop should be affixed with a 10~12cm skirt, which can cover the iron frame. After installation, it is sealed with silicone around the wall and the basin, no leakage.
6. Installation and acceptance of the toilet: It is mainly to check whether the toilet seat distance is reasonable, the pit distance is too small for the water tank to enter the wall, and the use and appearance have an influence; if the pit distance is too large, the toilet and the wall surface have a large space. The toilet should be installed firmly and should be fixed by expansion bolts. It must not be fixed with wood screws. The bottom of the toilet and the floor should not be connected with the cement mortar. The correct method is to seal the rubber around the perimeter to ensure watertight performance. Some toilets use a sealing rubber gasket instead of the sitting slurry, which can be used after the installation is firm. Sealed. The hand test method can be used for inspection, and there is no swing phenomenon. The toilet and water tank should be installed in an accurate position. The tolerance of the single piece position is 10mm, and the tolerance of the verticality should not be more than 10mm.
7. Installation and acceptance of the bathtub in the shower room: The installation and acceptance of the bathtub is very important. It is not only necessary to meet the standards of use, but also to consider the leakage incident and the residents in the immediate and downstairs. Therefore, the bathtub acceptance recommendation is carried out in two stages: after the installation of the skirt (there is no need to build the skirt in the skirt), the water should be tested several times before the tile is covered, and the flushing is smooth, and there is no leakage around the pavement, so there is no leakage. by. The drain of the bathtub should be connected directly to the nozzle of the water spout. Do not connect with the plastic hose, and at the same time oppose the drainage of the open drain under the cylinder. The basin surface is sealed with silicone rubber around the periphery of the wall. Acrylic bathtubs are caused by the weight of the human body and the dynamic load of the water. After a long time, it is easy to cause cracks in the wall. Therefore, the sealing of the silicone must be tight.
8. The water supply connecting pipe of sanitary ware shall not have the defects of concave and convex flattening. The connection with the inlet pipe and the sewage outlet must be tight and there must be no leakage.
Combination modularization electronic Truck Scale uses frame structured, has high overall rigidity and strong torsion resistant performance. The platform module is simple, and convenient for container transportation. It can form weighing system together with high accuracy shear beam Load Cell or Column Load Cell and Weighing Indicator with excellent performance, rich functions and multiple interfaces.
Its features are high accuracy, good reliability, high intelligence, strong adaptability and convenient installation, adjustment and maintenance.
Load Scales For Trucks,Portable Mobile Truck Scale,Electronic Combination Truck Scale,Combined Truck Scale
SHANDONG JINZHONG SCIENCE & TECHNOLOGY GROUP COMPANY LIMITED , https://www.chinagoldbell.com