The separation bearing of the internal combustion forklift clutch is frequently operated, and the number of damages accounts for a large proportion of the forklift failure. It is understood that if the driver is properly operated and timely, the bearing can be used for about 3 months, but it must be changed during the repair. new. If the driver's technical level is low, the forklift that is driven will have damage to the separation bearing almost every month. After the damage, other parts will be removed, such as the separation lever and the clutch plate, so that the material cost of equipment maintenance is obviously improved.
What is the cause of the damage of the clutch release bearing? In practice, although the driver is strictly required to dispense the oil to the release bearing every day, this is not only cumbersome, but the bearing is often damaged. According to the analysis, the high temperature of the engine is transmitted to the separation bearing, and the high-speed rotation of the bearing also generates high temperature. Under such conditions, the oil is difficult to remain in the bearing, the bearing works continuously under high temperature conditions, and the lubrication condition is not good. The cause of frequent damage.
In response to the above problems, it has also been tried to heat the bearing in the grease to allow the grease to penetrate into the bearing. After the treatment, the grease can fill the bearing, but the grease is destroyed due to the high temperature treatment. The amplitude is reduced, the effect of using this method is not ideal, and the service life of the bearing is not extended. We also used a sharp-mouthed grease gun to directly grease the release bearing. After installing the vehicle, the service life of the bearing is greatly extended after observation and inspection. This method of oiling has received satisfactory results, but the operation is more complicated. Then I explored the case where the engine was not disassembled, and the butter was added. Firstly, the test was successful on the 475C engine, and then it was tested on the 475C and 480 and 492 engines. Both of them received good results. After repeated practice, improvement, and summing up experience, a relatively simple method of oil injection operation was finally formed. The specific process is as follows:
(l) The engine does not disintegrate the oil filling method. First open the clutch cover to check the wear of the separated bearing. If it is confirmed that the bearing is not damaged or the wear is not over the limit, remove the clutch pedal, adjust the connecting rod pin, and make the separation bearing and its Return the seat to the last position, fill the hole of the bearing housing with a grease gun until the bearing overflows, then turn the bearing slightly, refill the oil, repeat the above work until there is a little butter around the bearing, then Rotate the bearing and observe the amount of oil. If there is resistance to the rotation of the bearing, it is proved that the bearing is filled with butter. Then remove a small amount of butter from the separation housing and reassemble the removed pin and clutch cover.
(2) Oil filling method of engine disintegration The engine is disassembled to expose the assembly of the separation bearing and the bearing housing, and the grease hole is used to refuel the small oil hole below the inner ring of the separation bearing housing. When the bearing has butter overflow, the bearing is rotated until the bearing one There are butter spills in the circle.
After the above two methods are treated, the bearings can be removed without oiling within half a year. After the trial of the oil filling method at Hengshui Railway Station, the mechanical integrity rate was significantly improved and significant economic benefits were achieved. It can save material costs; increase the loading and unloading volume, and increase the loading and unloading capacity by 30t per month. This method has also been promoted at other railway stations and has achieved satisfactory results.
Concerned about surprises
Label: How to extend the life of forklift clutch release bearing? How to extend the life of split bearing
Previous: How to fix the coupling? Coupling fixing method Next: How to choose the direction of opening the door?
DQOK is a bathroom factory specializing in the production of brass and stainless steel shower sets. We have sundry multi-functional Thermostatic Shower Set. The advantage with thermostatic valves is the direct control over output temperature; while your water heater can be set to 140° F to protect against bacterial contamination, the water coming out of your shower head can always be 100° F (a maximum output temperature is set on the valve).All products have patents, avant-garde design and unique innovation. Dingquan bathroom will be your priority
Thermostatic Shower Set,4 Functions Thermostatic Shower Set,Thermostatic Shower,Shower Select Set
Heshan Dingquan Sanitary Ware Industry Co., Ltd , https://www.dqoksanitary.com