3G three screw pump management

3G three screw Pump suction stop valve should be fully open in case of starting to prevent overload or suction air. Although the 3G three-screw pump with dry suction capacity, but must prevent dry rotation, so as not to scratch the work surface. If the pump needs to be started with very low oil temperature or high viscosity, it should be started with the suction valve and by-pass valve fully open to minimize the load when starting the pump. Until the prime mover reaches the rated speed, Bypass valve gradually closed. When the by-pass valve is opened, the liquid is circulated and circulated in the pump under the condition of throttling, and the more the circulating oil is, the longer the circulating time is, the more severe the heat of the liquid is, and even the pump factor High temperature deformation and damage, we must pay attention. Operation 3G three screw pump must be set in accordance with the direction of operation to produce a certain suction row. Pump work, should pay attention to check the pressure, temperature and mechanical seal work. Shaft seal should allow a trace of leakage, such as leakage does not exceed 20-30 seconds / drop, then that normal. If the pump is noisy at work, it is often caused by too low an oil temperature, too high a viscosity of the fluid, air entering the fluid, loss of coupling, or excessive wear on the pump. Parking pump stop, you should first close the discharge stop valve, and stop the pump fully stop after suction stop valve. Screw pump due to the larger working screw length, poor rigidity, easily lead to bending, resulting in abnormal work. Shaft connection must be well centered; the best work is to be carried out after the installation of positioning, so as not to cause deformation of the pipeline implicated; connection pipe should be independently fixed, as far as possible to reduce the implication of the pump. In addition, the spare screw, the best preserved in the use of hanging fixed method to avoid distortion caused by uneven placement of the third century BC, Archimedes invented the spiral rod, the water can be smooth and continuous to a few meters high , The principle is still used by modern screw pump.

Plier Series

Common types and uses of pliers
Pliers have many functions and are used in many industries. The pliers used in different industries are also different. Generally, the more commonly used pliers are:
1. Wire stripper
Wire strippers are commonly used tools for internal electricians, motor repairs, and instrumentation electricians. They are composed of knife edges, crimping ports and clamp handles. They are mainly used for stripping plastic and rubber insulated wires and cable core wires.
2. Wire cutters
Also called a vise, it is a kind of clamp and cutting tool. It is composed of jaws, tooth edges, knife edges, guillotines and pliers handles. It is mostly used to pick up nails or break nails and iron wires.
3. Nozzle pliers
It can be divided into electrical and electronic categories. It is mainly used for cutting injection molding machine products, plastic products, and injection nozzles. It is also suitable for cutting metal products and electronic component pins.
4. Needle-nose pliers
Also known as trimmers, pointed pliers, and pointed pliers. They are composed of pointed tips, knife edges and pliers handles. They are generally made of 45# steel. They are used to cut single and multi-strand wires with thinner diameters and to give orders. Stranded wire joint bending, stripping of plastic insulation layer, etc., can be operated in a relatively small working space.
5. Curved nose pliers
Also called elbow pliers, its function is similar to that of needle-nose pliers without cutting edge, and it is suitable for use in narrow or recessed working spaces.
6. Flat nose pliers
It is a commonly used tool for assembly of metal parts and telecommunications engineering. It is generally used to bend metal sheets and metal filaments to make them into the required shape. In repair work, they are used to install and pull out pins, springs, etc.
7. Diagonal pliers
Mainly used to cut metal wires, flat-nose diagonal pliers are suitable for use in recessed working spaces.
8. Top cutting pliers
End-cutting pliers are similar to diagonal pliers. They are mainly used for cutting steel wires with the cutting edge at the top.
9. Water pump pliers
The function is similar to a pipe wrench, but it is lighter, smaller and easier to use than a pipe wrench. However, the clamping force is not as good as a pipe wrench. Generally, it is only suitable for household non-professional emergency or simple installation of water pipes.
10. Slip joint pliers
The shape resembles a carp. The opening width of the jaws has two adjustment positions, which can be enlarged or reduced. It is mainly used to clamp round parts. It can also replace small nuts and small bolts with a wrench. It is often used in the auto repair industry.
11. Circlip pliers
Commonly known as circlip pliers, it is a special tool used to install inner and outer circlips, and can also be used to remove circlips. .
12. Vigorous pliers
It is mainly used for clamping parts for riveting, welding, grinding, etc. It can also be used as a wrench. Its characteristic is that the jaws can be locked and generate a large clamping force to prevent the clamped parts from loosening.

Wire Stripper,Needle-Nose Pliers,Wire Cutters,Curved Nose Pliers

Rugao Yaou Import & Export Trade Co., Ltd , https://www.ntyaous.com