The internal structure of the ONU broadband network box:
The internal structure of the ONU broadband network box is divided into four parts: the power distribution area, the fiber fusion area, the ONU equipment area, and the distribution area. It is equipped with a corresponding cable management ring to facilitate the management of the subscriber line. Completely isolated.
Distribution area:
It is recommended that the distribution area be equipped with 10A 2P of the same grade or the same grade to facilitate the introduction of external power; one maintenance socket (including three sockets of three holes) can facilitate the power supply of the external equipment on the site. If it is an outdoor cabinet, you need to add a lightning protection module separately.
The user is required to install a grounding bar in the ONU broadband network box and a surge protector must be installed at the power supply.
The wiring module and ONU equipment installed in the user's ONU broadband network box must be grounded.
Fiber fusion zone:
In order to save the internal space of the information box, the design of the fiber fusion zone needs to be accurately calculated. It can also be installed on the inner side panel of the information box without affecting other routing channels. The fiber fusion zone consists of fiber holder, splice tray and pigtail fiber. The column consists of three parts.
The fiber holder is used for fiber-reinforced core fixing and fiber-tightening of the information box, and is generally an 8-core cable.
The splice tray is used for the fiber into the box and the fiber jumper.
The disc fiber wheel is used to consolidate excess fiber jumpers.
The fiber fusion splicing unit generally uses a 6-port ODF integrated module or a 12-port ODF integrated module.
ONU equipment area:
The ONU equipment installation area adopts the standard 19-inch bracket design, and the ONU equipment is hoisted (or side mounted) on the bracket. If the installation is unstable, it is also considered to install the reinforcement bracket.
Considering the difference in the depth of ONUs of various manufacturers, in order to ensure that all types of ONUs can be installed normally, the reserved depth of the ONU equipment area is not less than 300 mm.
In addition, in order to facilitate the binding of the ONU subscriber line, several cable management loops are designed between the ONU and the distribution area.
Wiring area:
According to the plan, the wiring area module in the ONU broadband network box is divided into an inner line area and an outer line area, the device side subscriber line card is connected to the inner line module, the user side incoming line card is connected to the outer line module, and the inner and outer lines are connected by the jumper connection to open the user. .
In the PON+LAN application environment, only the POTS port jumpers need to be considered, so the internal and external line terminals have the same requirements. Considering the terminal redundancy, the device capacity can be configured by 2.5 times. The jumper module is arranged according to the left and right or the upper and lower lines and the outer line. In terms of space saving and cost considerations, it is recommended to configure 110 wiring modules (25 pairs, 50 pairs, 100 pairs, 200 pairs, etc.).
In the PON+DSL application environment, according to the common practice in the industry, the number of terminals required on the internal line side is (device narrowband capacity + device broadband capacity *2), the external line terminal is the same as the device capacity, and the number of security units is the same as the number of external line terminals. . It is recommended to configure the MDF subrack.
The MDF subrack national common module is 32 lines for the inner line and 25 lines for the outer line. Each manufacturer also has its own module. You can calculate the inner and outer line terminals before configuring the MDF module.
Related Reading:
Http://
Http://youlongxifeng.cn.gongchang.com
Http://youlongxifeng0.cn.gongchang.com
Http://
Doosan`s products are known for their durability, quality, and energy efficiency. As such, we want to see your Doosan machinery remain in use for as long as possible. If you need a replacement Doosan Final Drive motor, contact us today!Doosan Final Drive,Doosan Final Drive Assy,Doosan Travel Motor,Doosan Travel Gearbox,Doosan Final Drive Spare Parts,Doosan Drive Parts,Doosan Motor.
JUHENG are pleased to support operators with a wide range of genuine, OEM and quality replacement Doosan excavator final drives, swing drives, recoil springs and slew rings that are guaranteed to fit and perform to specification.
Doosan Excavator Final Drive, Hydraulic Pump and Other Components
Investigate below the stock availability for your Doosan excavator part. If a unit is available and you order before 3pm we despatch worldwide the same day.
An excavator final drive and Swing Motor assembly can be of two types: plug-in motor and gearbox, or totally integrated units. The design of your drive will dictate what options are available. The approaches adopted by final drive manufacturers and swing motor manufacturers are outlined below.
The model, serial and part number information can be found on the product plate; some examples are shown here. If it is missing or damaged, you may recognise your drive from the photos shown below. This will help your FDC Partner identify the correct replacement options.
Doosan Final Drive,Doosan Final Drive Assy,Doosan Travel Motor,Doosan Travel Gearbox,Doosan Final Drive Spare Parts,Doosan Drive Parts,Doosan Motor
Jining Juheng Hydraulic Machinery Co., Ltd. , https://www.jhexcavator.com